Most viewed - Amps & FX
|
Pedal board version 1213 viewsEffects: Boss TU-2 tuner; Morley Bad Horsey Vai 2 Wah*; Mesa Boogie V-Twin overdrive; Boss Chorus Ensemble CE-5; Boss DD-20 Giga Delay.
(* Replacement for Snarling Dogs Whino-Wah because it's easier to use.)
Amp controls: Overdrive; Voice (5 degrees of sound from thin to thick); Reverb.tone256
|
|
Amp and half stack206 viewsAmp: Matamp 1224. Special feature is that there is no increase in volume when switching in the overdrive. This mod. was made at my request; I can get additional volume and overdrive with the Mesa Boogie V-Twin. For more information on the amp, go to: http://www.jurassicrock.co.uk/matamp_1224.htm
212 Cabinet: Celestion G12M Greenback and Celestion G12H 70th Anniversary Special Edition wired in series giving about 40 watts at 16ohm. Used little after buying the Blackstar Artisan 15 and so sold.tone256
|
|
Pedal Board version 3170 viewsFurther modified to include the Voodoo Valve Pedal Power 2 Plus. See General "Non-Music Discussion - Powering Pedal Boards" for details. tone256
|
|
Pedal Board version 2140 viewsCHANGE: Taken out chorus and replaced with Keeley compressor.
REASON: Stopped using chorus after programmed more attractive "chorus like" sound into delay unit. Compressor thickens single coil sounds, which is useful for instrumentals in particular.
CHANGE: Layout from right to left instead of left to right.
REASON: Pedals have "in" on right & "out" on left. New layout makes cabling neater.tone256
|
|
Common effect board in case.94 viewsThe board was built to fit this case.tone256
|
|
Common effects board92 viewsBuilt for use with Artisan 15 and Matamp 1224. Replaces previous boards.
T-Rex Chameleon Fuel Tank power supply mounted on bottom to save space. All electric wiring and most signal wires underneath for neatness.
There are 8 units to power. Although the p.s.u. has only 5 outlets, each one provides 300 mA and so can power more than one unit, as follows: 1 (9v neg. centre) - tuner & chorus; 2 (9v neg. centre) - wah & delay; 3 (9v neg. centre) - noise gate & channel switch; 4 (18v neg. centre) - distortion; 5 (9v pos. centre) - receiver. The output from the Boss TU2 tuner will be used to power the indicator lights on the amp switches (voice, gain, reverb) when I use the Matamp.tone256
|
|
Common effects board91 viewsFor use with both Blackstar Artisan 15 and Matamp 1224. Replaces previous two effects boards.
Laid out ergonomically, i.e. the effects changed most often & most particularly during a song, are at the front.
Signal path is as per convention, i.e. radio receiver - tuner - distortion - wah - delay - chorus - noise gate - channel switch - amp.tone256
|
|
Small effects board88 viewsTop row from right to left: Samson AP1 wireless receiver, Boss TU2 tuner, Fulltone OCVD distortion.
Bottom row from right: MXR Carbon Copy delay, Morley ABY (switching or combining channels).
The signal chain is in the order described above.tone256
|
|
Bottom of small effects board showing T-Rex Fuel Tank Chameleon PSU80 viewsProvides 300mA from each output. 3 providing choice of 9v or 12v DC, 1 at 9v or 18v DC and 1 at 9v or 12v DC or 12v AC. Configured to provide 1 @ 12v DC + centre, 2 @ 9v DC - centre, 1 @ 9v DC + centre and 1 @ 18v DC - centre.tone256
|
|
Blackstar Artisan 1556 viewsAll valve, 1 x 12, 2 channel combo switchable between 5 and 15 watts. Having sold my Matamp 1224, this is now used exclusively for gigs. With the pedal board, it provides all the sounds I need and, with a Hughes & Kettner Red Box permanently fitted, is usually D.I.'d, so is plenty loud enough. Bought the Matamp Jazz & Bass because of its clean sound and headroom and so sold.tone256
|
|
Common effects board (revised) top view.49 viewsShowing introduction of compressor. Also, old sound gate replaced by new, better quality, which is now mounted on the bottom.
Signal path now: Samson Airline radio receiver - Boss TU2 Tuner - Keeley Compressor - Dunlop Baby Wah - Fulltone OCD Overdrive - Boss Chorus Ensemble CE5 - MXR Carbon Copy Analog Delay - MXR M135 Smart Gate - Channel selector switch.tone256
|
|
Common pedal board (revised) bottom.43 viewsPSU and sound gate mounted on bottom as they are both "set & leave" (so routine access not required). All electrics and some signal cables routed underneath to keep top uncluttered.tone256
|
|
Common pedal board (revised)39 viewsShowing back row raised to improve accessibility. TUner and chorus raised by 1/8 inch, compressor raised by 3/4 inch to bring them in line.tone256
|
|
Common pedal board (revised) side view.38 viewsShowing legs at front shorter than rear to incline towards me when playing making access easier.tone256
|
|
Channel switch out, Rothwell Atomic Booster in30 viewsSignal path: Guitar - Samson AP1 radio receiver - Boss TU2 tuner - Keeley compressor - Morley Maverick Mini Wah - Rothwell Atomic Booster - Fulltone OCD - Boss Chorus CE-2 - MXR Carbon Copy Analog Delay - MXR Smartgate - Amp. Power supply: 1. 9v negative centre: Boss TU2 tuner, Keeley compressor; 2. 12v positive centre: Samson AP1 radio receiver; 3. 9v negative centre: Morley Maverick Mini Wah, MXR Carbon Analog Delay, MXR Smartgate; 4. 18v negative centre: Fulltone OCD; 5. 9v negative centre: Rothwelltone256
|
|
Diago Effects Board28 viewsNew effects board based on Diago Gigman. Altered because I couldn't resolve unpredictable noise that I believed to be related to having PSU on underneath. Other advantage is that I am now able to use the noise gate selectively.
Signal path: guitar - radio receiver - Boss TU2 tuner - Keeley compressor - Morley Maverick mini wah (optical) - Fulltone OCD overdrive - Boss Chorus CE-2 - MXR Carbon Copy analog delay - MXR Smartgate - amp channel selector switch - amp.tone256
|
|
Now with T-Rex Tonebug chorus & flanger and ISP Decimator G-String noise gate26 viewsSignal path: guitar - wireless receiver - noise gate - tuner - compressor - wah - distortion - chorus/flanger - noise gate - delay - channel switch - amp. Power supply: 1. (9v neg) tuner & compressor; 2. (12v pos) wireless receiver; 3. (9v neg) wah, delay & channel switch; 4. (18v neg) distortion; 5. (9v neg) chorus/flanger & delay.tone256
|
|
Pedal Board upgraded with Shure GLXD 16 radio receiver/tuner18 viewsSamson Airline and Boss TU2 replaced with Shure GLXD 16. Added Rothwell Atomic Booster. Signal path: GLXD 16 - ISP Decimator (trigger only) - Keeley Compressor - Maverick Wah-Wah - OCD - Atomic Booster - Chorus/Phaser - ISP Decimator (signal) - MXR Analogue Delay - Channel Switch - amp. Power supply: 1. (9v -) noise gate, compressor; 2. (12v+) receiver/tuner; 3. (9v-) compressor, wah; 4. (16v -) overdrive; 5. (9v-) chorus/phaser, delay, amp switch.tone256
|
|
|